Care & Maintenance
Urbane Decor surfaces are built to be low-maintenance. No polishing, no painting, no sealing. A simple wipe keeps every finish looking new. Here is how to care for each surface, and what to avoid.
The everyday routine
The same simple routine works across almost every Urbane Decor finish.
Do this
- Dust with a dry or barely damp soft microfibre cloth.
- For marks, wipe with a cloth dampened in water with a little mild soap.
- Wipe dry; do not leave standing water sitting on joints or cut edges.
- Test any new cleaner on a hidden corner before using it on a visible area.
Never needed
- No polishing, waxing or buffing.
- No painting or re-coating.
- No sealing or sanding.
- No specialist machines or treatments.
What to avoid
A few things can dull or mark a finish. Keep these away from all surfaces.
- Abrasive pads, scouring powders and steel wool.
- Harsh solvents, thinners, bleach, acetone and strong chemical cleaners.
- Pressure washers or steam cleaners aimed directly at joints.
- Dragging sharp or heavy objects across the surface.
- Prolonged standing water on cut edges.
Care by material
The wipe-clean routine is the same; these are the specifics that matter per surface.
Fluted WPC, WPC and charcoal panels
Waterproof and termite-proof, so they suit bathrooms and kitchens. Wipe clean with mild soapy water and dry cut edges after heavy splashing.
ACP panels
Wipe with mild soapy water. On exterior facades, an occasional rinse clears dust and pollution film. No waxing or polishing.
PVC panels
Fully water-resistant; wipe clean. Avoid solvent-based cleaners, which can dull the printed layer.
Acrylic sheets and mirror
Use only a soft cloth with water or a dedicated acrylic cleaner. Never use ammonia-based glass sprays, which can craze acrylic over time.
Alabaster and UV marble sheets
Wipe with a soft damp cloth. Avoid acidic cleaners such as lemon or vinegar on stone-look surfaces.
Rattan cane webbing
Dust gently and keep away from prolonged damp. A light mist of water can re-tension a weave that has loosened slightly.
Epoxy and PU stone panels
Wipe with mild soapy water. Keep abrasives off the gloss so it stays clear.
HD biophilic and SOFTIQ panels
Dust dry or wipe with a barely damp cloth. SOFTIQ is clay-based, so keep it out of constant water contact.
Moisture, at a glance
Which surfaces belong in wet areas, and which prefer to stay dry.
Fine in wet areas
Fluted WPC, WPC, charcoal, PVC and ACP are waterproof or water-resistant and suit bathrooms, kitchens and splash zones. Wipe cut edges dry after heavy splashing.
Keep out of constant water
Alabaster, UV marble and clay-based SOFTIQ are moisture-tolerant for wiping but are not meant for constant immersion or standing water.
Quick do's and don'ts
Do
- Dust regularly.
- Use mild soap and water.
- Wipe dry after cleaning.
- Test new cleaners on a hidden corner.
Don't
- Use abrasives or strong solvents.
- Seal, paint or polish.
- Leave standing water on edges.
- Use ammonia sprays on acrylic.
Care FAQs
Dust regularly and wipe with a soft cloth dampened in water with a little mild soap, then wipe dry.
No. None of our finishes need sealing, painting, waxing or polishing.
Fluted WPC, WPC, charcoal, PVC and ACP are waterproof or water-resistant and suit wet areas. Wipe cut edges dry after heavy splashing.
Abrasive pads, scouring powders, bleach, thinners and strong solvents. On acrylic, also avoid ammonia-based glass sprays.
No. Ammonia-based sprays can craze acrylic. Use water or a dedicated acrylic cleaner with a soft cloth.
Need the spec for a specific finish?
Download the collection catalogue or message us and we will send the care sheet.